How much does an energy management system cost in Pakistan?
What drives the cost of an industrial energy management system in Pakistan, what to ask suppliers, and how to start small without overspending.
ES-IGW-E1 · All-in-One Controller
Sensor inputs, relay control and Modbus in one industrial gateway
The ES-IGW-E1 reads sensors directly on its analog and digital inputs, controls equipment through its relay outputs, and talks to meters and controllers over Modbus, RS485, RS232 and CAN bus. You configure it from a web dashboard.
Specifications
Technical specifications
| Ethernet | 2x (Internet + Modbus TCP) |
|---|---|
| Serial | 1x RS485, 1x RS232 |
| Fieldbus | CAN bus |
| Analog inputs | 4x (0–20 mA / 0–10 V, 16-bit) |
| Digital inputs | 8x (12–24 V) |
| Relay outputs | 8x, for actuator control |
| Power | 24V DC / 10A |
| Configuration | Web dashboard |
Use cases
What the ES-IGW-E1 is used for
Direct sensor monitoring
Wire temperature, pressure, flow or humidity transmitters with 0–20 mA or 0–10 V outputs straight into its four 16-bit analog inputs.
Status and alarm signals
Pick up running, fault or mains-failure signals on eight 12–24 V digital inputs.
Equipment control
Switch actuators such as pumps, fans or alarm sounders through eight relay outputs.
Mixed equipment on one gateway
Combine Modbus TCP and RTU, RS232 and CAN bus devices with direct sensors, at sites where equipment comes from many vendors.
Industries
Where it's used
Pharmaceuticals
HVAC, cleanroom utilities and compressed air monitoring for compliance and uptime.
Textiles
Machine health on looms and spinning lines, plus energy per production unit.
Food & Beverage
Boiler, chiller and compressed-air monitoring, plus production line uptime.
Chemicals & Fertilizer
Pump, motor and utility monitoring for continuous processes.
Data Centers & Telecom
Mains, generator, fuel and DC power monitoring, plus panel alarms, across distributed sites.
Cold Storage
Temperature monitoring, compressor health and instant alerts on power loss.
Commercial Buildings
Multi-meter energy tracking, plus HVAC and generator costs per floor or tenant.
Packaging
Line uptime, motor and VFD health, and compressed air leak detection.
Compare
Compare the gateways
| Feature | ES-IGW-B1 | ES-IGW-E1 (This gateway) |
|---|---|---|
| Best for | Best for collecting data from existing meters and controllers. | Best for sites that need direct sensor inputs and equipment control. |
| Ethernet | 2x (Internet + Modbus TCP) | 2x (Internet + Modbus TCP) |
| Serial | 1x RS485 | 1x RS485, 1x RS232 |
| Fieldbus | Not included | CAN bus |
| Analog inputs | Not included | 4x (0–20 mA / 0–10 V, 16-bit) |
| Digital inputs | Not included | 8x (12–24 V) |
| Relay outputs | Not included | 8x, for actuator control |
| Power | 5V DC / 3A | 24V DC / 10A |
| Configuration | Web dashboard | Web dashboard |
FAQ
ES-IGW-E1 FAQ
Which sensors can I connect?
Any sensor with a 0–20 mA or 0–10 V output on the four 16-bit analog inputs, and 12–24 V signals on the eight digital inputs.
Can it control equipment?
Yes. Eight relay outputs switch actuators such as pumps, fans or alarm sounders.
What power does it need?
24V DC at 10A.
Can it also read meters and PLCs like the ES-IGW-B1?
Yes. It has the same two Ethernet ports (internet and Modbus TCP) and RS485, plus RS232 and CAN bus.
Related articles
View all postsLive demo
See En-Stream on your site
Book a 30-minute demo and see how En-Stream connects to the meters, machines and generators you already run.
Request a Demoor call +92-332-2158347