ES-IGW-B1
Data Concentrator
The ES-IGW-B1 reads ATS panels, energy meters and other Modbus devices over Modbus TCP and RS485.
- Ethernet
- 2x (Internet + Modbus TCP)
- Serial
- 1x RS485
- Power
- 5V DC / 3A
- Configuration
- Web dashboard
Data Centers & Telecom
Power, fuel and site monitoring for data centers and telecom sites
Every site depends on mains, generators, DC power and fuel, often with nobody there to watch them. En-Stream brings ATS readings, breaker status, DC current, fuel levels and panel alarms from every location into one live view, and alerts your team the moment something changes.
The problem
Why distributed sites are hard to run
Outages are found after the fact
A tripped breaker, a failed changeover or a generator that won't start is often discovered only when the site goes down.
Fuel goes missing
Diesel is bought for every generator, but without tank levels it's hard to tell consumption from refills, and refills from pilferage.
Panels are opened unseen
Doors on power and DC panels are opened, and smoke or heat builds up, without anyone knowing until the next visit.
Every site visit costs time
Checking meters, tanks and panels in person across many sites is slow and expensive, and still leaves gaps between visits.
What to measure
Readings that matter at data centers and telecom sites
En-Stream reads these from ATS panels, meters and DC panels, or from sensors and contacts wired to a gateway.
Mains and generator ATS
Line voltages, phase currents, power per phase, frequency and energy, for both the utility supply and the generator.
Breaker and changeover status
Which incomers and load breakers are on, off or tripped, and whether the site is running on mains or generator.
Fuel tanks
Level, litres available, consumption, refills and pilferage, for underground tanks and generator tanks.
DC power
Current on every shunt across your DC panels, so the DC load is visible panel by panel.
Panel conditions
Front and back door status, smoke alarms, temperature and humidity for each AC and DC panel.
Trends over time
Current, kW, kVA and voltage graphs, to spot load growth and supply problems early.
Dashboards
Dashboards network and site teams use
Custom Dashboards
ATS readings, panel status, fuel tanks and DC shunts, each on its own screen, laid out the way your sites are wired.
Alarms & Alerts
Alarms on breaker trips, mains failure, low fuel, a drop in tank level, open doors, smoke or high temperature, sent the moment they happen.
Energy Flow
Grid, generator and solar feeding each site, live, and which source carries the load.
Hardware
Gateways for data centers and telecom sites
ES-IGW-E1
All-in-One Controller
The ES-IGW-E1 adds direct inputs: door contacts, smoke alarms and breaker status on its digital inputs, and temperature, humidity and fuel level sensors on its 0–20 mA / 0–10 V inputs.
- Ethernet
- 2x (Internet + Modbus TCP)
- Serial
- 1x RS485, 1x RS232
- Fieldbus
- CAN bus
- Analog inputs
- 4x (0–20 mA / 0–10 V, 16-bit)
- Digital inputs
- 8x (12–24 V)
- Relay outputs
- 8x, for actuator control
- Power
- 24V DC / 10A
- Configuration
- Web dashboard
FAQ
Data center and telecom monitoring FAQ
Can En-Stream detect fuel theft?
Yes. Tank monitoring tracks the level, consumption and refills of each tank and flags pilferage, so fuel that leaves the tank without being used shows up straight away.
Can we see whether a site is on mains or generator?
Yes. ATS readings and breaker status show which source is feeding the site, and alarms tell your team when it changes over or a breaker trips.
Can En-Stream monitor DC power?
Yes. It reads the current on each DC shunt, panel by panel, alongside the AC readings from the ATS.
Can we see all our sites in one place?
Yes. Every site reports to the same platform, and remote access lets your team open any site's dashboards from any device.
How does data get from a remote site to the platform?
Gateways send data, encrypted, to the platform over Ethernet, Wi-Fi or GSM.
Live demo
See En-Stream on your site
Book a 30-minute demo and see how En-Stream connects to the meters, machines and generators you already run.
Request a Demoor call +92-332-2158347
More industries
Energy and machine monitoring for other industries
Pharmaceuticals
HVAC, cleanroom utilities and compressed air monitoring for compliance and uptime.
Textiles
Machine health on looms and spinning lines, plus energy per production unit.
Food & Beverage
Boiler, chiller and compressed-air monitoring, plus production line uptime.
Chemicals & Fertilizer
Pump, motor and utility monitoring for continuous processes.
Cold Storage
Temperature monitoring, compressor health and instant alerts on power loss.
Commercial Buildings
Multi-meter energy tracking, plus HVAC and generator costs per floor or tenant.
Packaging
Line uptime, motor and VFD health, and compressed air leak detection.